HUAWEI CDMA BTS 3606 PDF

Default Re: Huawei CDMA E BTS Max Power??? HI I think it can be more than 20W because the RF board support MAX 60W. The 3rd Global CDMA Operation and Development Forum, themed. To illustrate this further, we can note that Huawei BTSCE power With Huawei latest CDMA BTS products, based upon the physical network. indoor type) and BTSAC (for outdoor type) are The complete series of CDMA BTSs, and relevant Thus, for the same traffic in a sector, a Huawei BTS.

Author: Darisar Sam
Country: Portugal
Language: English (Spanish)
Genre: Education
Published (Last): 5 March 2010
Pages: 457
PDF File Size: 8.20 Mb
ePub File Size: 4.7 Mb
ISBN: 278-7-95912-479-6
Downloads: 20165
Price: Free* [*Free Regsitration Required]
Uploader: Vim

For the specific method, see section 2. To remove cabinet doors, do it in a reverse order. It is divided into six chapters: Table of Contents Add to my manuals Add. Connect one end of the cable to the working ground of the EAC. They are used for the convenience of installation description.

Fasten the three bolt sets in the following order: Note, Comment, Tip, Knowhow, Thought: This manual also for: The engineering supervisor does not submit self-test report on quality of the engineering hardware.

To print the manual completely, please, download it. The letters A, B, C as shown in Figure are not cable labels. The packing case is in good condition. Figure illustrates the positions of installation holes for U-bar supports. Page 14 – Power Supply Conditions of the Equipment The panel is clean without obvious damage.

  HUMAX HDR 1000S USER MANUAL PDF

Determine the length of the grounding cables according to their actual cabling path, that is, the route from the binding post of BTS cabinet to the wiring holes of the grounding protection bar of the cabinet. Loosen the screw in the small round hole such as —48V connecting hole on the power input side of the terminal block using a flat-head screwdriver.

CDMA grows greener – Huawei Publications

Wooden cases are generally used to pack heavy objects like huqwei, batteries, and so on. Positioning the Cabinet and Removing the Floor Caution: Lead the bolts through the lower support. Got it, continue to print. Anchor bolt for the floor d expansion bolt d height-lock bolt first in the middle, then on both sides To fix the support, proceed as follows: Route the alarm cables coming in from the other side of the enclosure through the cabling holes on both sides of the 8-E1 module and then to the respective slots.

Don’t show me this message again. Feed back the situation to the local Huawei Representative Office. Determine the installation location for the DDF huswei to the engineering design for the equipment room.

Lead the cables into their corresponding cable-fixing troughs. Installing Power Cables For the 24 V power input, the voltage drop of the cable from the 24 V power supply system to the power bt port of the BTS must be less than or equal to 0.

  ANALISIS Y DISENO DE SISTEMAS DE INFORMACION SENN PDF

Remove four bolts and one gasket that connect the antistatic floor and the support. Means a complementary description. Figure Installing a board 2 Tighten the screws clockwise on the front panel, as shown in Figure If the outer package is damaged or soaked; or the equipment is soaked and becomes rusty, stop unpacking and find the cause. This chapter describes how to install and use these two types of DDF.

Conducting Insulation Test To conduct an insulation test, proceed as follows: This section introduces how to install the power module and what to pay attention during the installation.

That is, 1 m 39 in. Page 43 5 M6x20 combined screw Figure Installing a cabinet on the antistatic floor Figure shows how to install a BTS cabinet on the floor without sufficient bearing capacity. Installing the Lower Support To install the lower support, proceed as follows: The color of the coat must be the same as or similar to that of the cabinet.

Huawei BTS3606 Installation Manual

Clamp the cables to the bracket. Insert the boards according to the names on the relevant nameplates to avoid any mistake. Please feel free to contact our local office or company headquarters.

Related Posts