Service Manual, Elna DE Details. Elna Model DE Serger Machine Service Manual, 20 Pages. The physical copy of the instruction manual is a soft cover. Full text of “Elna Serger Instruction Manual dse de e” IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic. Hi there, Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this.

Author: Voodooran Mazurg
Country: Niger
Language: English (Spanish)
Genre: Science
Published (Last): 4 May 2010
Pages: 408
PDF File Size: 8.83 Mb
ePub File Size: 7.80 Mb
ISBN: 701-8-16915-671-6
Downloads: 13222
Price: Free* [*Free Regsitration Required]
Uploader: Faull

Answer questions, earn points and help others Answer questions. A A A Foot Pressure With the guide line a of the pressure control knob even with the top cover surface bthe foot pressure is suitable for most kinds of fabrics and rarely needs adjusting.

If the fabric tends to pucker, guide it by gently pulling it to the back with your left hand, and at the same time lightly holding it with your right hand, for good stitching results.

Loosen the needle clamp screws a with the Allen screwdriver bto remove the old needles. Safety Device Model The front door is provided with a safety device. To lower the presser foot swing the lever c up. Upper elma thread – Yellow thread guides 2. However, you can easily change the stitch length by shifting the stitch length slide a between 0. Rolled hem foot 4mm elnausa. Finally thread the right needle from front to back, then under the foot, leaving about 10 cm of the thread to the left.


Lubrication When using your machine for the first time, or if you have not used it for some time, put a few drops of oil on the point indicated.

The fabric is not moving it just keeps sewing in the same place. Remove the sewing foot see page 5. How can I fix it please?

Remove the needle you are not using the same as for 3-thread use and the upper thread from the machine. Have a manual for Elna Sewing Machines? We congratulate you on your choice and hope that elnw will give you lasting satisfaction. Please enter a valid email address.

Removing Stitches from Sewn Fabric 1. You are then ready to start the next seam.

Full text of “Elna Serger Instruction Manual dse de e”

It’s worth a thousand words. For spools with a large diameter, place the cone holders higher up on the spool pins or place them with the widest end on top see illustrationso that the spools can be seated firmly on the spool pin base.

Unfortunately, it appears there are no free downloads. Open the front door. Then cut the thread with the thread cutter see illustration. Provide your email address and model I will send it. To engage the lever ctake the same steps, pull the knob d to the right, and then swing it up. Unscrew the light bulb and replace the bulb by following the same procedure in the reverse order. I can email for free. Posted on Aug 28, If the plug does not fit fully in the outlet, reverse the plug.


Press preferably with the sole of the foot, not with the toes. By pushing the differential feed slide c down to a higher number, the front feed dog a moves the fabric faster, as shown. After sewing extra heavy fabrics, always loosen this screw slightly, to unlock the blade for normal sewing.

A manual for elna 614DE – Elna Sewing Machines

Cone Holders and Caps Both industrial and domestic type thread spools can be used on the machine. I have freestanding Series 8 dishwasher. Your machine is equipped with two feed dogs a and beach of which moves independently. Instant Repair Help over the Phone 6ya. For very special fabric types, however, you might at times, want to adjust the cutting width.

Follow the threading paths carefully, in accordance with the charts inside the amnual door, in the sequence To fit the 2-thread convertor on to the upper looper bfirst insert the tip of the convertor into the upper looper eye from the back, then snap the other end securely into the hole c of the upper looper.

Threading the Right Needle – Coloured red on the chart and on the thread guides.

Threading the Upper Looper – Coloured yellow on the chart and on the thread guides.

Related Posts