DATASHEET 2N2219 PDF

The 2N, 2N, 2N and 2N are sili- con planar TO (for 2N and 2N) and in Jedec . This datasheet has been download from. Semelab encourages customers to verify that datasheets are current before Test Conditions. Min. Typ. Max. Unit. LAB. SEME. 2N IC = 10mA. IB = 0. Sep 2. Philips Semiconductors. Product specification. NPN switching transistors. 2N; 2NA. FEATURES. • High current (max.

Author: Arashimi Zololar
Country: South Africa
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 19 July 2007
Pages: 194
PDF File Size: 11.1 Mb
ePub File Size: 20.84 Mb
ISBN: 401-3-40735-595-9
Downloads: 71958
Price: Free* [*Free Regsitration Required]
Uploader: Mokree

Philips – datasheet pdf

Current flows in through collector, normally connected to load. Submitted by admin on 21 June Where Vcc is the voltage on which the load operates and V BE is the voltage across the Base and Emitter which in our case according to the data sheet 1.

Another important thing to keep in mind, while using a transistor as switch is the base resistor. Overall it is just another small signal transistor which is commonly used in switching and amplifying circuits. To make this current flow through the transistor the value of base current I B can be calculated using the below formula:. Complete Technical Details can be found at the datasheet given at the end of this page. Since transistor is of NPN the load to be switched should be connected to the collector and the emitter should be connected to the ground as show in the figure below.

  6ES5 100-8MA02 PDF

In our case for a collector current of mA we have to pass a base current of 16mA. The 2N is a NPN transistor and is normally used as a switch in many circuits. So to calculate the resistor value of datashet base we can use the formulae. Amplifier modules like Audio amplifiers, signal Amplifier etc.

2N2219 Datasheet, Equivalent, Cross Reference Search

Where h FE, is the current gain of the transistor which in our case is As we know the transistor is a dtaasheet controlled device meaning, we have pass some current I B thorough the base of the transistor to turn it on.

When this transistor is fully biased then it can allow a maximum of mA to flow across the collector and emitter.

The value of this current can be calculated by the required amount of current 2n22219 will be consumed by the load. But this calculation will lead to the closest value to start with. So if you looking for an NPN transistor that could switch loads or for decent amplification then 2N might the right choice for your project.

When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV. Here lets us assume the load here consumes around mA maximum daasheet our collector current I C mA. Current Drains out through emitter, normally connected to ground.

  DISMANTLING THE DUTCH DEFENSE WITH THE DANGERFIELD ATTACK PDF

To bias a transistor we have to supply current to base pin, this current I B should be limited to 5mA by using a transistor to the base pin. To make this current flow through the transistor the value of base current I B can be calculated using the below formula: This resistor is connected to the base pin of the transistor 2n22219 limit the current flowing through the base.

TL — Programmable Reference Voltage. But it comes in a metal can package and can operate dafasheet voltages slightly higher than what a 2N can handle.

However this vale will not be very accurate because the transistor will have an internal voltage drop across the collector current, so it mostly experimental to get the maximum current from the transistor.

So the value if R B will be. The maximum amount of current that could flow through the Collector pin is mA, hence we cannot connect loads that consume more than mA using this transistor. This stage is called Saturation Region.

Related Posts